EN 362:2004 Connectors

 

EN 362:2004 Connectors

Connectors come in a variety of shapes and sizes for different applications and are used to connect components together within a fall protection system.

Major / Minor Axis Static Strength

The major axis tests a connector in the main direction of loading. The load required depends on the connectors class – see below table. Many connectors claim a higher rated load on the major axis than the minimum within the standard and for the purposes of certification are required to show evidence that this higher load can be sustained for 3 minutes also.

The minor axis test is applicable to connectors where it is possible for them to be loaded in the opposite direction to the Major axis. The test is to ensure that should the connector be accidentally loaded or misused across the minor axis, then it still has strength to take the forces generated in a fall.

Description

Major axis Gate closed and unlocked (kN)

Major axis Gate closed and locked (kN)

Minor axis Gate closed (kN)

Basic connector
(class B)

15

20

7

Multi-use connector
(class M)

15

20

15

Termination connector
(class T)

15

20

N/A

Anchor connector
(class A)

15

20

N/A

Screwlink connector
(class Q)

N/A

25

10

Gate Function

This test loads the major axis of a connector to a force of 6kN (excludes class A connectors). The connector is required to hold this force for 10 seconds and then be able to open, close and lock the gate

Gate Resistance (Face / Side)

The gate face test is carried out on connectors by applying a force directly to the gate of 1kN for 90 seconds. During the test the gate cannot separate from the latch by more than 1mm and following the test the gate should still function correctly

The gate side test is carried out on connectors by applying a force directly on the side of the gate of 1.5kN for 60 seconds. There shall be nor partial fracture of the connector and following the test the gate shall still function correctly

Corrosion Resistance

Metallic components used in fall protection equipment are subjected to a neutral salt-spray test intended to prove a minimum resistance to environmental corrosion (specifically rust). Products are held within a sealed chamber, which is filled with a salt-water mist, which can induce rust in unprotected metals. Products are subjected to 48 hours exposure and examined for rusting and function afterward.

 Resource

Comments

Post a Comment

Popular posts from this blog

EN 1497: 2007 Rescue Harnesses

  EN 1497: 2007 Rescue harnesses   Rescue harnesses are used when it is required to lower or raise an individual, normally in the event of an emergency. A rescue attachment point may be incorporated into a full body harness used in a fall protection system allowing a user to be rescue following the event of a fall. Ergonomics To ensure a rescue harness has a relative degree of comfort, ergonomic trials are carried out on two users with differing weights and heights. This test requires each user to be suspended for 4 minutes and then assessed by visual inspection and questions to see if there was an acceptable level of comfort. Dynamic Performance Rescue harnesses are subjected to a drop test to generate a shock load on the product. A lesser force is applied to a rescue harness attachment point compared with fall arrest harness attachments as the possibility of a period of free-fall is significantly less in use. Rescue harnesses are subjected to a 1 metre drop using...
Read more

EN 354:2010 Lanyards

  EN 354:2010 Lanyards   Lanyards intended for use in connecting the attachment point of a harness to a suitable anchorage device. This type of lanyard is intended for use as a component of a larger system, which should include a shock absorbing element. Slippage Lanyards are subjected to a force of 6kN for 3 minutes, before then being assessed for slippage through the adjustment element which cannot be anymore than 50mm. This test is done following ambient conditioning and after being placed in water and a freezer at -4°C. There is also an optional test for extreme cold for any products claiming use in temperatures below -30°C. This test is only applicable for lanyards that include an adjustment element. Static Strength Metallic lanyards are subjected to a tensile force of 15kN and non-metallic lanyards are subjected to a tensile force of 22kN for a minimum period of 3 minutes. This test is done following ambient conditioning and after being placed in water and a ...
Read more

SATRA-Fall Protection-test

  SATRA-Fall Protection Testing of fall protection equipment is typically carried out on the whole product as presented for sale, although testing and approval of components (such as connectors) can be carried out where they are interchangeable between larger products. In addition, consideration must be paid to the whole system of fall protection, including worn components, components carried and/or operated, and the method of fixation to the structure. Any fall protection system needs to consider a number of factors, including: ·          the distance the user falls before being brought to a halt ·          the force applied to the user’s body throughout the arrest of the fall ·          the likelihood of introducing additional hazards, such as ‘swing-falls’ (or ‘pendulum effect’) or the striking of sharp objects ·       ...
Read more